Tesla Sentry Mode: What It Is, How to Use It and Battery Drain

Tesla's Sentry Mode captures videos from up to four cameras at once

Not a Tesla App

Tesla Sentry Mode is an intelligent vehicle security system designed to monitor and record potential threats around your parked Tesla. This feature utilizes the vehicle's cameras and sensors to detect suspicious activity, notify the owner through the Tesla mobile app, and save footage to a USB drive.

What is Sentry Mode

When enabled, Tesla Sentry Mode keeps the vehicle's cameras and computer powered on and ready to record potential threats while the car is locked and in Park. If a threat is detected, the system pulses the headlights, displays a message on the touchscreen, and may sound the alarm, depending on the situation. In addition, footage of the event is saved to a USB drive, and the owner will be notified via the app if the alarm goes off. Sentry Mode offers an extra layer of security for Tesla owners, helping to deter would-be thieves or vandals.

Cameras and Sound

While Sentry Mode is enabled, it will record from four of the vehicle's nine available cameras. The video recorded comes from one of the front-facing cameras, the fender camera on either side of the vehicle, and the rear camera. The other remaining front-facing cameras, B-pillar cameras, and the cabin camera do not record at this time.

Teslas do not contain any external microphones, so all Sentry Mode videos are silent. Although Teslas do contain internal microphones, Tesla does not capture audio from these microphones. In fact, even if you're viewing the interior camera in the Tesla app, you can not hear any audio from inside of the vehicle.

How to Turn On Sentry Mode

You can enable Sentry Mode by tapping Controls then tapping 'Sentry.' The Sentry Mode icon will turn red when Sentry Mode is enabled. You can also choose to turn on Sentry Mode automatically when the vehicle is parked or activate it using the Tesla mobile app. Voice commands like "Keep Tesla safe," "Keep my car safe," "Sentry on," or "Enable Sentry" can also be used to enable the feature.

Enable Sentry Mode from the Controls menu

Not a Tesla App

How Long Does Sentry Mode Stay On

Once Sentry Mode is enabled, it will remain on until you turn it off, or when your battery reaches 20%. If the battery falls below this level, Sentry Mode will turn off, and you will receive a notification via the Tesla app. Since Sentry Mode increases power consumption, Tesla turns it off automatically to leave you with enough energy to reach your destination.

Sentry Mode Battery Drain

Since your vehicle's computer needs to remain on to process video from its various cameras, there is additional power usage while Sentry Mode is enabled.

The actual amount of power consumed varies based on your vehicle's specific hardware, but tests have shown that the vehicle will consume about 250 to 300 watts while Sentry Mode is on. This is equivalent to losing about 1 mile of range for every hour Sentry Mode is enabled.

In a day, Sentry Mode may consume as much as 7.2 kWh, about 24 miles of range, or roughly equivalent to 7% to 14% of your battery, depending on your model and battery size.

Since Sentry Mode consumes so much energy, it's best to use it only when needed. Sentry Mode is not meant for when your vehicle will be parked long term, as it'll quickly drain your battery. Luckily, Tesla offers options to automatically enable Sentry Mode at specific locations and Sentry Mode is automatically disabled when the vehicle's battery falls to 20%.

Sentry Mode Options

You can customize Sentry Mode settings to fit your preferences and requirements. Some options available include:

Disabling sounds: If you want to silence the security alarm and audio system when the alarm is triggered, navigate to Controls > Safety > Disable Sentry Sounds. Sentry Mode will still send a notification through the mobile app and save the last 10 minutes of footage of any events that occurred.

Excluding specific locations: In Controls > Safety > Sentry Mode, you can choose not to enable Sentry Mode in particular areas, such as your home, work, or favorite destinations. This can be helpful if you want to conserve battery power or avoid unnecessary recordings in familiar areas.

Choosing the clip length: In some markets (Not available in the U.S. and Canada), you can select the length of Sentry Mode video clips, allowing you to customize how much footage is saved during an event. 

Disabling camera detection: If you prefer, you can disable camera detection so that Sentry Mode only activates when the car senses a physical intrusion. This can be helpful in situations where you want to minimize the number of false alarms or unnecessary recordings.

How to Set Up Sentry Mode

First, insert a compatible USB drive into the glove box USB port. If your car doesn't have a USB port in the glove box, you can use one in the center console. Note that not all Teslas have data-capable USB ports in the center console, so the glove box should be your first choice. Chances are that Tesla already included a compatible USB drive in the car for you. Tesla defines a compatible USB drive as one that is USB 2.0 compatible and holds at least 64 GB. This Samsung USB drive is a good choice for Sentry Mode because of its durability and size. It offers fast write speeds and 256GB of storage, 4x Tesla's recommendation.

Next, you can format the USB drive by going to Controls > Safety and tap on "Format USB Drive." Tesla recommends using a high-quality USB drive to ensure smooth recording and playback of Sentry Mode videos. You can also enable Dashcam recording. Navigate to Controls > Safety > Dashcam in your vehicle's menu and set it to Auto. This will allow your vehicle to automatically record footage while driving. Footage will automatically be recorded when an event is detected or when you tap the Dashcam icon under Controls > Dashcam.

How to View Sentry Mode Recordings

You can review your Sentry Mode video with the Dashcam Viewer app in the car

Not a Tesla App

To view Sentry Mode or Dashcam videos, use the Dashcam app in your vehicle. The Tesla system tags events with a red dot, making locating and reviewing footage easier. This feature allows you to quickly identify any incidents around your vehicle and gather evidence if necessary. Remember to regularly check your USB drive's storage capacity, as new recordings will overwrite the oldest ones when the drive is full. It's a good idea to back up important footage to a separate storage device for safekeeping.

Sentry Mode Live Access

You can view live footage from your vehicle in the Tesla app

Not a Tesla App

Sentry Mode Live Access lets you view your vehicle's cameras in real-time using the Tesla mobile app. This feature requires Tesla's Premium Connectivity. When using View Live Camera, your vehicle will periodically flash its exterior lights and displays a message on the touchscreen, notifying others that the area surrounding the vehicle is being viewed through the cameras.

To enable the View Live Camera feature, touch Controls > Safety > Sentry Mode > View Live Camera via Mobile App on the car's touchscreen. First, ensure no occupants are in the vehicle, and all doors are locked. Then, navigate to Safety > Sentry Mode > View Live Camera in the Tesla app. The live camera feed is fully encrypted and cannot be accessed by Tesla, ensuring your privacy. View Live Camera is limited to approximately one hour (or 15 minutes for some regions) of cumulative usage per day. Although Sentry Mode Live Access is widely available, it is not currently available in all markets.

If your vehicle is equipped with a pedestrian warning speaker you can press and hold the microphone button in the app to transmit your voice through the speaker, potentially deterring would-be intruders or vandals.

When Dog Mode or Sentry Mode are enabled, you can also switch the live camera view to see through the vehicle's interior camera. This can be useful if you want to check on your pet while away from the vehicle. Note that this feature is not supported in vehicles with Autopilot computer 2.0 or 2.5.

Tesla Sentry Mode is a valuable security feature that can help protect your vehicle from potential threats. By following the steps provided, you can set up, enable, and customize this feature to fit your needs. As a Tesla owner, using Sentry Mode can give you peace of mind, knowing that your car is actively monitoring its surroundings for potential threats. While no security system can prevent all attacks, Sentry Mode offers an added layer of protection that can help deter criminals and keep your vehicle safe.

NHTSA Probes Tesla’s Robotaxi Plans; Seeks Answers on FSD in Poor Weather

Not a Tesla App

As anticipation builds for Tesla’s Robotaxi network debut in Austin, potentially just a few short weeks away, the National Highway Traffic Safety Administration (NHTSA) is turning its official eye onto Tesla. The ask? How will Tesla’s FSD handle the unpredictable realities of challenging weather?

The NHTSA Request

The NHTSA has sent a formal letter to Tesla, which was made public on May 12th, requesting detailed information about Tesla’s Robotaxi service. The NHTSA inquiry centers specifically on the safety and performance of FSD when faced with reduced visibility conditions like rain, fog, and sun glare. The request is tied to an ongoing NHTSA investigation, which was initiated in October 2023, examining Tesla’s FSD and Autopilot suite following incidents in poor visibility.

Tesla’s executives, including Elon Musk, have previously stated that the company is full steam ahead to launch Robotaxi in Austin this June. However, NHTSA’s pointed questions come even as Tesla has recently discussed its plans to work on region-specific and weather-specific FSD training.

Tesla’s executive leadership acknowledged the need to adapt the system to diverse environmental and weather conditions. Now, regulators want specifics on how Tesla intends to address environmental conditions and how that translates to operational safety for the fleet.

Request Breakdown

NHTSA’s letter outlines a need for detailed information from Tesla before the service launches and covers several key areas. We’ve broken this down into various sections below:

Deployment Scale

NHTSA is looking for the exact number of vehicles and models that will be part of the initial Austin fleet, and what the projected service availability times would be for said fleet. Tesla has previously said it’d launch with 10-20 Model Ys, but looks like NHTSA is looking for additional details.

Oversight

In terms of oversight, NHTSA is looking to confirm whether the Robotaxis will operate under real-time supervision of Tesla’s employees, either remotely or in-vehicle.

This is a question on our minds as well. A recent app update suggested that Tesla could have a driver in the vehicle, but it wasn’t clear whether this was referring to Tesla’s own fleet or customer-owned vehicles. The only thing we have heard officially from Tesla is that Tesla “may” use remote support, but that they were still looking into it.

Adverse Weather Capabilities

This is the meat and potatoes of the request - how will Tesla ensure safety during sun glare, fog, heavy rain, snow, or dust? What specific protocols are triggered if poor visibility is encountered mid-trip? Will the vehicle pull over or call home and cancel rides?

Sensor Technology

Surprisingly, NHTSA is looking for details regarding the vehicle the Robotaxi sensor suites and how Tesla intends to use those sensors to ensure safe operation under varied conditions. NHTSA has had previous submissions from Tesla in regard to its sensor suite and how it uses the technology, so it feels odd that they are requesting another batch - but this could be related to the use of the next generation of FSD (Unsupervised).

Compliance

Does Tesla’s FSD system adhere, either fully or partially, to established industry standards for autonomous driving? This likely refers to the NHTSA Automated Vehicles for Safety guidebook, which lays out the “L0 to L5” driver assistance vs automation system.

Future Expansion

Finally, NHTSA is looking for the timeline for enabling Robotaxi functionality on vehicles not directly owned or controlled by Tesla. Tesla has already come out and said that customer-owned vehicles wouldn’t be allowed on the robotaxi network until 2026, but obviously, NHTSA wants to hear directly from Tesla and likely has more specific questions covering a wide variety of potential issues.

These questions will likely have to be answered with considerable amounts of data and justification for the NHTSA. Once all that is done, Tesla will be in a better position to receive regulatory approval at a larger scale than just within the city of Austin or the state of Texa with the NHTSA’s backing.

Successfully addressing this letter will be the key for Unsupervised FSD moving forward, but Tesla hasn’t issued a public response to the agency’s letter, and likely won’t in a public manner. So we’ll have to wait and see how the launch of the Robotaxi network pans out next month.

Follow

Follow

Follow

FSD V13.2.9 Rolls Out for HW4 as Part of Tesla’s 2025.14.6 Update

Not a Tesla App

After an 84-day wait since the last FSD update, Tesla has finally begun rolling out a new version of FSD V13 to its AI4-equipped vehicles. This new release, V13.2.9, is rolling out to all vehicles, including the Cybertruck.

Unfortunately, since it’s a minor point release (from V13.2.8), the release notes are the same, and Tesla hasn’t included a change log or changed what’s coming in the future.

Software Update 2025.14.6

The FSD update is rolling out with Tesla software update 2025.14.6. Interestingly, update 2025.14.6 is seeing a wider distribution and is also being made available to vehicles without FSD and outside North America. For those vehicles, this update just includes bug fixes.

TCU Fix

There’s one fix in particular that’s expected to be included in this update, according to a message from Tesla Service. In earlier 2025.14 updates, there was a bug in some vehicles that prevented some vehicles from falling asleep properly due to a Telematics Control Unit (TCU) issue. This bug caused additional battery drain since some of the vehicle’s systems remained on.

Tesla Service said they planned to include a bug fix in update 2025.14.6, but it hasn’t been confirmed whether the fix actually made it out in this release.

Early Access Users and More

FSD v13.2.9 was first rolled out to Tesla’s standard Early Access group, including well-known community members and content creators. It has also reached participants in the newer, Texas-based Early Access Program, suggesting that the update is relatively stable and may serve as a foundation for upcoming FSD releases.

Tesla could be intending to use the Texas Early Access Program to test various features, perhaps related to the upcoming Robotaxi network launch in Austin. While this is plausible, it is merely speculation, and we’ll be keeping a close eye on that group to see what exactly Tesla does.

HW3 Users

While Tesla has recently been including FSD updates for HW3 and HW4 in the same release, this update does not include any changes for HW3 users. HW3 vehicles that are receiving this update are staying on FSD V12.6.4, which means that whichever fixes this update includes they’re specific to FSD V13 or HW4.

Point Release - Not Much New

Being a point release, V13.2.9 isn’t expected to introduce any major new capabilities. Tesla hasn’t provided specific release notes detailing changes from V13.2.8.

Hopefully, Tesla has taken into account recent user feedback on V13.2.8 about lane centering and lane selection, and this update addresses some of those issues. However, early feedback is that those issues are still present.

There is always potential for a more substantial update in the near future, so keep your fingers crossed, but after such a long wait, we expected more to be included. It seems like Tesla may have felt the need to address a bug in this release instead of waiting for the next major release, which is expected to either be FSD V13.3 or FSD V14.

Roll Out

The fact that Software Update 2025.14.6 is going out wider than the Early Access audience suggests that Tesla is confident in this release and that it likely only includes very minor changes. We expect this update to continue going out over the coming days.

Follow

Follow

Follow