You can enable Full Self-Driving (Beta) by tapping 'Control' > 'Autopilot' > 'Full Self-Driving (Beta)' and following the instructions.

Full Self-Driving is in early limited access Beta and must be used with additional caution. It may do the wrong thing at the worst time, so you must always keep your hands on the wheel and pay extra attention to the road. Do not become complacent. When Full Self-Driving is enabled your vehicle will make lane changes off highway, select forks to follow your navigation route, navigate around other vehicles and objects, and make left and right turns. Use Full Self-Driving in limited Beta only if you will pay constant attention to the road, and be prepared to act immediately, especially around blind corners, crossing intersections, and in narrow driving situations.

Your vehicle is running on Tesla Vision! Note that Tesla Vision also includes some temporary limitations, follow distance is limited to 2-7 and Autopilot top speed is 85 mph.

- Enabled FSD Beta on highway. This unifies the vision and planning stack on and off-highway and replaces the legacy highway stack, which is over four years old. The legacy highway stack still relies on several single-camera and single-frame networks, and was setup to handle simple lane-specific maneuvers. FSD Beta's multi-camera video networks and next-gen planner, that allows for more complex agent interactions with less reliance on lanes, make way for adding more intelligent behaviors, smoother control and better decision making.

- Improved recall for close-by cut-in cases by 15%, particularly for large trucks and high-yaw rate scenarios, through an additional 30k auto-labeled clips mined from the fleet. Additionally, expanded and tuned dedicated speed control for cut-in objects.

- Improved the position of ego in wide lanes, by biasing in the direction of the upcoming turn to allow other cars to maneuver around ego.

- Improved handling during scenarios with high curvature or large trucks by offsetting in lane to maintain safe distances to other vehicles on the road and increase comfort.

- Improved behavior for path blockage lane changes in dense traffic. Ego will now maintain more headway in blocked lanes to hedge for possible cans in dense traffic.

- Improved lane changes in dense traffic scenarios by allowing higher acceleration during the alignment phase, This results in more natural gap selection to overtake adjacent lane vehicles very close to ego

- Made turns smoother by improving the detection consistency between lanes, lines and road edge predictions. This was accomplished by integrating the latest version of the lane-guidance module into the road edge and lines network.

- Improved accuracy for detecting other vehicles' moving semantics. Improved precision by 23% for cases where other vehicles transition to driving and reduced error by 12% for cases where Autopilot incorrectly detects its lead vehicle as parked. These were achieved by increasing video context in the network, adding more data of these scenarios, and increasing the loss penalty for control-relevant vehicles,

- Extended maximum trajectory optimization horizon, resulting in smoother control for high curvature roads and far away vehicles when driving at highway speeds.

- Improved driving behavior next to row of parked cars in narrow lanes, preferring to offset and staying within lane instead of unnecessarily lane changing away or slowing down.

- Improved back-to-back lane change maneuvers through better fusion between vision-based localization and coarse map lane counts.

- Added text blurbs in the user interface to communicate upcoming maneuvers that FSD Beta plans to make. Also improved the visualization of upcoming slowdowns along the vehicle's path. Chevrons render at varying opacity and speed to indicate the slowdown intensity, and a solid line appears at locations where the car will come to a stop.

- Improved the recall and precision of object detection, notably reducing the position error of semi-trucks by 10%, increasing the recall and precision of crossing vehicles over 100m away by 3% and 7%, respectively, and increasing the recall of motorbikes by 5%. This was accomplished by implementing additional quality checks in our two million video clip autolabeled dataset.

- Reduced false offsetting around objects in wide lanes and near intersections by improving object kinematics modeling in low speed scenarios.

- Adjusted position of Automatic Blind Spot Camera when FSD Beta is active to prioritize the Autopilot visualization. Drag the camera to save custom positions.

For maximum safety and accountability, use of Full Self-Driving (Beta) will be suspended if improper usage is detected. Improper usage is when you, or another driver of your vehicle, receive five 'Forced Autopilot Disengagements'. A disengagement is when the Autopilot system disengages for the remainder of a trip after the driver receives several audio and visual warnings for inattentiveness. Driver-initiated disengagements do not count as improper usage and are expected from the driver. Keep your hands on the wheel and remain attentive at all times. Use of any hand-held devices while using Autopilot is not allowed.

The FSD Beta feature can only be removed per this suspension method and it will be unavailable for approximately two weeks.

Go to Controls > Service to see how many miles it's been since your last tire service.

When you get your tires rotated, replaced, or swapped, tap 'Reset'.

You can also go to Controls > Service > Wheel and Tire > Tire to input your tire configuration. This tells your car to reset the learned tire settings to improve your driving experience.

Go to Controls > Service to see how many miles it's been since your last tire service.

When you get your tires rotated, replaced, or swapped, tap 'Reset' to reset the counter.

Large text size feature is now available in all supported languages.

To update your settings, go to Controls > Display > Text Size.

The Pinyin keyboard now features an expanded dictionary and other improvements.

Type abbreviated or full input, then select an option from the candidate window. Your most commonly used candidates are shown first, and after you select one, the window shows suggestions based on your choice.

Windshield wiper controls have now been added to the list of options that you can control in Scroll Wheel Function.

The steering wheel customization feature lets you control a variety of vehicle settings directly from the steering wheel. You simply long press the left scroll wheel and you can scroll through various settings and options such as HVAC fan speed, rear camera and more.

You can customize the list of options shown, or add the windshield wiper functionality to the list by navigating to Controls > Display > Scroll Wheel Function.

If you use your phone as a key for your Tesla, the device name that shows up in Bluetooth settings now has a more intuitive name.

The device name used to be a string of 18 characters without the word Tesla anywhere in the name, leaving some users wondering what the mystery may be.

As of this update, the vehicle key will now be displayed as "Tesla" followed by the last six characters of the vehicle's VIN.

In some regions, Tesla is now displaying an updated Data Sharing policy. The new policy allows you to enable or disable several additional options for data sharing. Enabling some or all of these options allows Tesla to collect additional data from your vehicle to improve Autopilot and other features.

Tesla makes it clear that they do not sell your data, that the data is anonymized, and that it's only used to improve their products. The one exception that Tesla mentions is if there is a 'safety critical' event, which may cause camera data to be linked to your vehicle.

You can allow Tesla to collect data for Autopilot, additional start and end drive data, which includes Summon and Park Assist, data when your vehicle is parked, and cabin camera analytics.

When searching for a destination in the vehicle's navigation system, the search results will now display which destinations are open and which are closed.

You can now enable the 'PIN to Drive' feature directly from the Tesla app. Simply navigate to Security & Drivers, toggle it on and set your PIN.

Having the ability to enable PIN to Drive in the app is useful for owners who may normally not use it, but may want to remotely enable the feature if they lose their key fob or phone.

This feature requires app update 4.21.5 or higher.

You can now preview more than just the cabin camera in your Tesla. By navigating to Controls > Service, you can now preview all nine (eight on hardware 4.0) of Tesla's cameras. This includes being able to view all the front-facing cameras and B-pillar cameras for the first time.

You can change cameras by tapping the name of the camera at the top of the live video.

Note: These camera views are only here to give customers a better understanding of what their vehicle can see and to confirm that the cameras are working correctly. There is no additional functionality gained from this feature, at this time.

The 'Current Trip' odometer metrics have been updated with this update. Instead of displaying kWh, the Current Trip odometer will now display the number of minutes elapsed since the vehicle was put into drive.

The other odometers, such as 'Since Last Charge', 'Trip A' and 'Trip B' still display kWh.

The app launcher at the bottom of the screen will now only display the driver's climate setting if there is no one sitting in the passenger seat.

If someone sits in the passenger seat, the passenger temperature setting will automatically appear.

Go to Controls > Service to see how many miles it's been since your last tire service.

When you get your tires rotated, replaced, or swapped, tap 'Reset'.

You can also go to Controls > Service > Wheel and Tire > Tire to input your tire configuration. This tells your car to reset the learned tire settings to improve your driving experience.

Go to Controls > Service to see how many miles it's been since your last tire service.

When you get your tires rotated, replaced, or swapped, tap 'Reset' to reset the counter.

Large text size feature is now available in all supported languages.

To update your settings, go to Controls > Display > Text Size.

The Pinyin keyboard now features an expanded dictionary and other improvements.

Type abbreviated or full input, then select an option from the candidate window. Your most commonly used candidates are shown first, and after you select one, the window shows suggestions based on your choice.

Windshield wiper controls have now been added to the list of options that you can control in Scroll Wheel Function.

The steering wheel customization feature lets you control a variety of vehicle settings directly from the steering wheel. You simply long press the left scroll wheel and you can scroll through various settings and options such as HVAC fan speed, rear camera and more.

You can customize the list of options shown, or add the windshield wiper functionality to the list by navigating to Controls > Display > Scroll Wheel Function.

If you use your phone as a key for your Tesla, the device name that shows up in Bluetooth settings now has a more intuitive name.

The device name used to be a string of 18 characters without the word Tesla anywhere in the name, leaving some users wondering what the mystery may be.

As of this update, the vehicle key will now be displayed as "Tesla" followed by the last six characters of the vehicle's VIN.

In some regions, Tesla is now displaying an updated Data Sharing policy. The new policy allows you to enable or disable several additional options for data sharing. Enabling some or all of these options allows Tesla to collect additional data from your vehicle to improve Autopilot and other features.

Tesla makes it clear that they do not sell your data, that the data is anonymized, and that it's only used to improve their products. The one exception that Tesla mentions is if there is a 'safety critical' event, which may cause camera data to be linked to your vehicle.

You can allow Tesla to collect data for Autopilot, additional start and end drive data, which includes Summon and Park Assist, data when your vehicle is parked, and cabin camera analytics.

When searching for a destination in the vehicle's navigation system, the search results will now display which destinations are open and which are closed.

Photo by Garth Schanock

You can now enable the 'PIN to Drive' feature directly from the Tesla app. Simply navigate to Security & Drivers, toggle it on and set your PIN.

Having the ability to enable PIN to Drive in the app is useful for owners who may normally not use it, but may want to remotely enable the feature if they lose their key fob or phone.

This feature requires app update 4.21.5 or higher.

You can now preview more than just the cabin camera in your Tesla. By navigating to Controls > Service, you can now preview all nine (eight on hardware 4.0) of Tesla's cameras. This includes being able to view all the front-facing cameras and B-pillar cameras for the first time.

You can change cameras by tapping the name of the camera at the top of the live video.

Note: These camera views are only here to give customers a better understanding of what their vehicle can see and to confirm that the cameras are working correctly. There is no additional functionality gained from this feature, at this time.

The 'Current Trip' odometer metrics have been updated with this update. Instead of displaying kWh, the Current Trip odometer will now display the number of minutes elapsed since the vehicle was put into drive.

The other odometers, such as 'Since Last Charge', 'Trip A' and 'Trip B' still display kWh.

The app launcher at the bottom of the screen will now only display the driver's climate setting if there is no one sitting in the passenger seat.

If someone sits in the passenger seat, the passenger temperature setting will automatically appear.

This update also includes the release notes for FSD Beta 11.3.6, with availability in the U.S. and Canada. It's not clear yet whether FSD Beta is exposed to the end user, but it looks like Tesla is close to, if they haven't already merged FSD Beta updates with regular production updates.

Tesla Vision Park Assist provides visual and audio alerts of surrounding objects. This feature uses the occupancy network to predict high-definition outlines of objects 360 degrees around the car.

Note: Tesla Vision Park Assist is for guidance purposes only and is not a substitute for an aware driver. Please be attentive and avoid obstacles as required.

Enable or disable data sharing and learn more about how Tesla uses anonymous data to improve existing safety and convenience features and create new ones.

Go to Controls > Software > Data Sharing. For more information on how we protect your data, go to www.tesla.com/privacy.

Choose the amount of regenerative braking applied when you release the accelerator pedal.

Standard: Provides the maximum amount of regenerative braking. When you release the accelerator pedal, your vehicle will slow down.

Low: Limits regenerative braking. When you release the accelerator pedal, your vehicle will take longer to slow down and coast farther than if set to "Standard".

Go to Controls > Pedals & Steering > Regenerative Braking. See Owner's Manual for more information.

The power meter is a thin horizontal line above the car status area of the touchscreen that shows real-time power usage.

The right side of the power meter represents power that is used to accelerate the vehicle. Now, when you press the accelerator pedal farther, the line is thicker.

With Track Mode, you can now:

- Reach a top speed of 200 mph when the optional Track Pack is installed.

- Monitor vehicle health at a glance with updated visuals on the instrument panel and touchscreen.

- Extract maximum track performance using adaptive suspension, torque vectoring and traction control systems, which have been updated to improve consistency and driver confidence.

Please refer to the Owner's Manual for more details.

Control your phone calls from the steering wheel. Use the left scroll button to answer or decline incoming calls. While you're on a call, use it to mute/ unmute yourself or hang up.

Choose Standard or Large text size for the touchscreen.

Go to Control > Display > Text Size

Do more with the left scroll button on the steering wheel. You can adjust settings like brightness and Acceleration Mode, or perform actions like toggling the Camera App, opening the glovebox, and saving Dashcam footage.

Long press the left scroll button to bring up a list of functions and scroll through the list. To choose which function comes up by default, go to Controls > Display > Scroll Wheel Function.

Use the 'Search' function for quicker access to controls and settings.

Go to Controls > Search and enter a search term. Make changes directly from the result or tap the link to jump to that panel in Controls.

A chime now sounds when you shift gears. To toggle gear chimes, go to Controls > Safety > Gear Chimes.

Adjust the passenger seat from the rear touchscreen to make it easier to enter or exit the rear seat. To access the passenger seat controls, tap the seat icon on the rear touchscreen. Hold one of the arrows to move the passenger seat forward or backward.

The controls are available only when the vehicle is not moving. To access the same controls from the front touchscreen, tap the App Launcher and go to the rear screen remote control app.

See photos and reviews when you select a point of interest or Supercharger location.

British English is now available as a voice recognition language.

To update your voice recognition language, go to Controls > Display > Voice Recognition Language and choose an option from the list.

Speed Assist now leverages your car's cameras to detect speed limit signs. This improves the accuracy of speed limit data on local roads and highways in select countries. Detected speed limit signs will be displayed in the driving visualization.

Make video calls with Zoom using the interior cabin camera.

If you have a Zoom meeting in your Calendar, tap the link to automatically start or join your meeting. Participant video and screen sharing is only visible while parked and will switch to audio-only if you drive. It is the driver's sole responsibility to consult and comply with all local regulations while using Zoom.

To access Zoom, tap Application Launcher > Zoom. For more information about Zoom, see the Owner's Manual.

Learn basics like creating Driver Profiles, using Phone Key and regenerative braking from the 'Get to Know Your Tesla' educational experience within the new 'Manual' app. Each topic includes a visual and, if applicable, a link to the relevant feature.

The 'Manual' app also provides easy access to resources for learning much more about your Tesla, such as the on-screen Owner's Manual and online tutorial videos. Go to App Launcher > Manual.

Enter text by writing characters with your fingers, then selecting from the candidates shown above the handwriting pad.

You can now set your vehicle's name through the Tesla app. To set your vehicle's name, simply tap the current name of your Tesla at the top of the app. You can then rename your vehicle and press 'OK.'

Photo by Twitter/Walgermo

Automatic Emergency Braking can now stop for vehicles traveling in a perpendicular path to your vehicle, such as a vehicle running a red light at an intersection.

Automatic Emergency Braking has also been improved to support higher speeds. It will can now be automatically activated at speeds up to 124 mph (200 km/h), up from a previous maximum of 90 mph (150 km/h).

In addition to these improvements, Automatic Emergency Braking can now stop for threats while traveling in reverse, although the functionality is limited.

The vehicle visualization that appears while your vehicle is parked and contains labels to lock/unlock your car, as well as open your trunk/frunk can now be rotated to view the vehicle from different angles.

The font for the speedometer has been made bolder to be easier to see.

Photo: KyleCoolky

When searching for destinations in your vehicle’s navigation system, each destination will now display the distance in miles/km from your current location.

In addition, the map pin now looks more like a button, which brings up the destination information on the map, instead of navigating to it.

While the functionality hasn't changed, your car will now display a plus sign (+) next to music controls to favorite a song. The plus sign replaces the heart icon in the music player.

Photo: StianWalgermo

You can now adjust the windshield wiper speed by using the scroll wheel on the steering wheel. First, press the button at the end of the left stalk to activate the windshield wipers and have the controls appear on the screen.

You can then tilt the left scroll wheel left/right to cycle through the various speeds of the windshield wipers.

Photo: LexBarker

You now have more control over your air suspension. In the suspension menu, you now have toggles for enabling or disabling a vehicle's height or speed at a specific location.

The ride height is now also expressed in inches in the U.S.

Photo: LuizFl

Tesla Theater now features square, app-like icons, instead of larger, horizontal logos.

Photo: StianWalgermo

All available options will now be displayed when you open the app drawer. Previously, options such as Frost Defrost and Wipers only showed up when you were customizing the launcher.

There is now a Customize button at the top of the app drawer as well.

Tesla will now display a "NEW" badge next to new features or options. This makes new features more noticeable when scrolling through menus.

The charging menu in the car has been updated to remove the car visualization and make the charging slider larger.

Photo: Drill on TFF Forum