Reset the learned tire settings directly after a tire rotation, swap, or replacement to improve your driving experience. To reset, tap Controls > Service > Wheel & Tire Configuration > Tires.

Customize how your car appears on the touchscreen and mobile app with the Car Colorizer. Change the color of your car's exterior by tapping Controls > Software > Colorizer icon, or using Colorizer in the ToyBox.

Your navigation voice guidance is now available in Polish. To switch your language setting, tap Controls > Display > Voice Navigation Language.

Your navigation voice guidance is now available in Turkish. To switch your language setting, tap Controls > Display > Voice Navigation Language.

The cabin camera above your rearview mirror can now determine driver inattentiveness and provide you with audible alerts, to remind you to keep your eyes on the road when Autopilot is engaged. Camera images do not leave the vehicle itself, which means the system cannot save or transmit information unless you enable data sharing. To change your data settings, tap Controls > Software > Data Sharing on your car's touchscreen. Cabin camera does not perform facial recognition or any other method of identity verification.

The cabin camera above your rearview mirror can now determine driver inattentiveness and provide you with audible alerts, to remind you to keep your eyes on the road when Autopilot is engaged. Camera images do not leave the vehicle itself, which means the system cannot save or transmit information unless you enable data sharing. To change your data settings, tap Controls > Software > Data Sharing on your car's touchscreen. Cabin camera does not perform facial recognition or any other method of identity verification.

Speed Assist now leverages your car's cameras to detect speed limit signs. This improves the accuracy of speed limit data on local roads and highways in select countries. Detected speed limit signs will be displayed in the driving visualization.

Your internet radio service provider has been switched to EtherealSound, providing an improved selection of radio stations and content for your drive.

Sentry Mode continuously monitors your car's surroundings while it's locked and parked. When enabled, the car automatically enters the Standby state with its cameras and sensors remain powered to detect potential threats and trigger an appropriate response state: Alert or Panic. To enable Sentry Mode, go to Controls > Safety > Sentry Mode.

If a minimal threat is detected, such as someone leaning on your car, Sentry Mode switches to the Alert state, displaying a message on your touchscreen indicating that cameras are recording.

If a major threat is detected, such as someone breaking a window, Sentry Mode switches to the Panic state. In this state, the touchscreen increases to maximum brightness, and you receive a notification on your mobile app.

To save the video clip captured while in Sentry Mode, you must insert a formatted USB flash drive into one of your USB ports beforehand. Sentry Mode requires more than 20% battery to operate. If your battery falls below 20% while the feature is active, Sentry Mode turns off and you receive a notification on your mobile app.

Note that Sentry Mode is designed to enhance the security of your car, but cannot protect your car from all possible threats.

Editor's note: This feature only applies to Israel. Sentry Mode has been added with some minor modifications to support local laws (no sound when the alarm sounds). If you already have Sentry Mode, it will continue to be available as it was before.

This enhancement builds upon your vehicle's superior crash protection - based upon regulatory and industry standard crash testing- by now using Tesla Vision to help offer some of the most cutting-edge seat belt pretensioner performance in the event of a frontal crash. Your seat belts will now begin to tighten and protect properly restrained occupants earlier in a wider array of frontal crashes.

Tesla Adaptive Suspension will now adjust ride height for an upcoming rough road section. This adjustment may occur at various locations, subject to availability, as the vehicle downloads rough road map data generated by Tesla cars. The instrument cluster will continue to indicate when the suspension is raised for comfort. To enable this feature, tap Controls > Suspension > Adaptive Suspension Damping, and select the Comfort or Auto setting.

With the introduction of v11, Tesla added HomeLink controls that appear when you're geographically close to one or more of the HomeLink devices.

The buttons feature a label underneath them that up until this update displayed whether tapping the button would cancel the the auto-open feature or activate the HomeLink device.

With this update Tesla has swapped these labels. The Activate or Cancel (if auto-open is turned on) text will now appear inside of the button, and label given to the device such as 'Left Garage' will now appear underneath the button.

Image by SparkyTX on TeslaMotorsClub

A chime will play when the traffic light you are waiting for turns green. If you are waiting behind another vehicle, the chime will play once the vehicle advances unless Traffic-Aware Cruise Control or Autosteer is active.

Note: This chime is only designed as a notification. It is the driver's responsibility to observe their environment and make decisions accordingly.

Editor's note: This feature no longer appears to require EAP or FSD.

Tesla's navigation system will once again display your estimated range upon arrival at your destination near your estimated time of arrival.

The Bluetooth menu has been updated to make it more obvious which device is connected and new device icons have been added.

Previously Tesla used to show a Bluetooth logo to the right of the device name. The logo would be blue if the device was connected or gray if it wasn't.

The Bluetooth icon has been replaced with a device icon, presumably so that Tesla can support various types of devices in the future, such as Bluetooth headphones and Bluetooth controllers.

If a device is connected, it will now display the text 'Connected' underneath the device name, along with a green dot.

Photo credit: @tesla_adri/Twitter

You can set Autopilot to start when you pull down the right stalk once, rather than twice. To choose this setting, go to Controls > Autopilot > Autopilot Activation > Single Pull.

Be aware that with Single Pull, when Autopilot Features is set to Autosteer (Beta), you'll bypass Traffic-Aware Cruise Control. Similarly when Autopilot Features is set to Full Self-Driving (Beta), you'll bypass Autosteer (Beta) and Traffic-Aware Cruise Control.

With Single Pull, when you cancel Autosteer (Beta) or Full Self-Driving (Beta), whether you take over the steering or push up the stalk one time - you'll immediately return to manual driving.

As with all Autopilot features, you must continue to pay attention and be ready to take immediate action including canceling the feature and returning to manual driving.

Speed Assist now leverages your car's cameras to detect speed limit signs. This improves the accuracy of speed limit data on local roads and highways in select countries. Detected speed limit signs will be displayed in the driving visualization.

Destination Charging sites that charge on a pay-per-use basis now show how many stalls are available.

Service Mode has been updated with various new panels and improvements.

The new panels include a new software section that lets you verify the software version installed and diagnose issues related to infotainment center, Autopilot and maps. There is a new section for 'High Voltage Interlock Loop,' as well as a new option in the Air Suspension panel that lets you inflate the air suspension reservoir.

Other changes include Chinese language support and a new feedback section for Service Mode Plus users.

Service Mode should only be accessed by technicians and owners who are familiar with it and aware of the risks involved. The vehicle should not be driven with Service Mode engaged, as various safety features are turned off.

You can set Autopilot to start when you pull down the right stalk once, rather than twice. To choose this setting, go to Controls > Autopilot > Autopilot Activation > Single Pull.

Be aware that with Single Pull, when Autopilot Features is set to Autosteer (Beta), you'll bypass Traffic-Aware Cruise Control. Similarly when Autopilot Features is set to Full Self-Driving (Beta), you'll bypass Autosteer (Beta) and Traffic-Aware Cruise Control.

With Single Pull, when you cancel Autosteer (Beta) or Full Self-Driving (Beta), whether you take over the steering or push up the stalk one time - you'll immediately return to manual driving.

As with all Autopilot features, you must continue to pay attention and be ready to take immediate action including canceling the feature and returning to manual driving.

Speed Assist now leverages your car's cameras to detect speed limit signs. This improves the accuracy of speed limit data on local roads and highways in select countries. Detected speed limit signs will be displayed in the driving visualization.

Destination Charging sites that charge on a pay-per-use basis now show how many stalls are available.

Service Mode has been updated with various new panels and improvements.

The new panels include a new software section that lets you verify the software version installed and diagnose issues related to infotainment center, Autopilot and maps. There is a new section for 'High Voltage Interlock Loop,' as well as a new option in the Air Suspension panel that lets you inflate the air suspension reservoir.

Other changes include Chinese language support and a new feedback section for Service Mode Plus users.

Service Mode should only be accessed by technicians and owners who are familiar with it and aware of the risks involved. The vehicle should not be driven with Service Mode engaged, as various safety features are turned off.

Please check back shortly. If you have received 2022.20.5, you can share release notes with us below.